Product Description
STL200-LED Outdoor Sensors Stealth 200 Sensor 300W Max Bronze from RAB Lighting is a STEALTH outdoor sensor designed with a special 200° detection pattern for wide side-to-side coverage. This bronze sensor is excellent for building perimeter protection and includes lens masks that allow customization of the detection zone.
Product Summary
- Detection Pattern: 50' x 200°
- Voltage: 120V
- Switching Capacity: 8 amps
- LED Load Rating: 300W LED
- Finish: Bronze
- Free shipping on orders over $250
Product Benefits
- Provides wide side-to-side outdoor motion detection for building perimeter protection.
- Helps keep lights on only when needed with an adjustable time setting from approximately 5 seconds to 12 minutes.
- Allows the detection zone to be customized with lens masks and adjustable sensitivity.
- Supports night-only or 24-hour operation using the photocell adjustment.
Key Features
- 200° detection pattern: Detects motion across a 50' x 200° coverage area.
- Compatible with LED lamps: Rated for 300W on LED fixture.
- Temperature compensation: Helps maintain sensor performance in changing outdoor conditions.
- Radio frequency immunity: Designed to resist interference from radio signals.
- 6000 volt surge protection: Provides surge protection for outdoor sensor applications.
- LED detection & "on guard" indicator: Red LED shows the sensor logic state and indicates a security device in operation.
- Protected manual override with auto reset: Allows manual nighttime control from a conventional indoor switch or circuit breaker.
- Can be wired in parallel: Supports wiring configurations for additional fixture control.
Specifications
Technical Specifications
| Product | STL200-LED |
| Color | Bronze |
| Weight | 1.0 lbs |
| Voltage | 120V |
| Switching Capacity | 8 amps |
| LED Load Rating | 300W LED |
| Power Consumption | 1 watt |
Performance Specifications
| Detection Pattern | 50' x 200° |
| Time Adjustment | 5 seconds to 12 minutes |
| Sensitivity Adjustment | 30% to 100% |
| Factory Sensitivity Setting | 100% |
| Factory Time Setting | 5-8 minutes |
| Surge Protection | I.E.C specs |
Physical Specifications
| Height | 3 1/2" / 8.9 cm |
| Width | 5" / 12.7 cm |
| Depth | 5" / 12.7 cm |
| Recommended Mounting Height | 6-12 feet |
| Mounting | Wall or ceiling mounted |
Compliance & Safety
| UL Listed | Raintight Photoelectric Switch |
| Location Rating | Suitable for wet locations |
| Warranty | 10-year sensor warranty |
Applications
- Building perimeter protection
- Outdoor security lighting control
- Wall-mounted or ceiling-mounted motion detection
- Areas where movement is expected across the detection pattern
- Night-only or 24-hour sensor-controlled lighting operation
Installation Tips
- Turn off all power at circuit breaker/fuse panel before installation.
- Read entire Installation Manual before proceeding.
- All wiring should comply with local electrical codes and requires a qualified electrician.
- The total lighting load connected to a STEALTH must not exceed 8 amps or 300W on LED fixture.
- Mount 6-12 feet high for optimum range and detection.
- Choose a location so that the sensor can “see” all paths of movement.
- Sensor functions best when the direction of expected movement is across its detection pattern, not towards the sensor.
- Sensor must be below and as far as possible away from lights.
- Do not install sensors on a circuit that feeds motor loads like kitchen appliances, HVAC equiptment, washer/dryer, or garagedoor openers.
Frequently Asked Questions
What is the detection pattern for the STL200-LED?
The STL200-LED has a 50' x 200° detection pattern for wide side-to-side coverage.
What voltage does this sensor use?
This sensor operates at 120V.
What is the maximum LED load rating?
The STL200-LED is rated for 300W on LED fixture with an 8 amps switching capacity.
Can the time setting be adjusted?
Yes. The time adjustment can be set from 5 seconds to 12 minutes.
Can this sensor be used in wet locations?
Yes. The STL200-LED is suitable for wet locations and is UL Listed as a Raintight Photoelectric Switch.
What mounting height is recommended?
Mount 6-12 feet high for optimum range and detection.
Can the sensor be wall or ceiling mounted?
Yes. The sensor may be wall or ceiling mounted.
Does the STL200-LED include manual override?
Yes. It includes protected manual override with auto reset and can be controlled by a conventional indoor switch or circuit breaker at night only.
